4T-6692, 4T6692 Track Loader Bolt-on Center Blade

Specification:
Part No.    4T-6692, 4T6692
Weight    10 Kg
Brand Name   OEM AVAIABLE
Replacement Brand  Caterpillar (CAT)

 

REQUEST FOR PARTS QUOTE

4T-6692, 4T6692 Track Loader Bolt-on Center Blade, CAT Bolt-on Cutting Edge Segment, Segment Edge Protection 30mm, BOLT ON LOADER SEGMENT, Caterpillar LOADER END BIT, 943 953 Loader End Edges, Replaceable Bolt On Cutting Edge and End Bit, Replacement CAT style Wheel Loader Edge, Double beveled reversible DBF bucket blade, CAT Wear Spare Parts China Supplier

4T-6692, 4T6692 Track Loader Bolt-on Center Blade, Replacement Aftermarket OEM Parts  4T-6692, 4T6692 Bucket Cutting Edge Suitable for Loader, Backhoe, Buy Blade & End Bit CAT genuine, new parts with delivery, aftermarket, replacement and not original Caterpillar .

4T-6692 BLADE SEGMENT CTR 25 X 280 X 195 963 955 943 939
WEIGHT
10kg
DIMENSION
25
PROFILE
two
WIDTH
280
LENGTH
195

COMPATIBLE MODELS FOR PART NUMBER 4T-6692
TRACK-TYPE LOADER
943 939 939C 953

Replacement Cutting Edges
We stock and supply high wear cutting edges for the following types of machinery:
Loaders
Scrapers
Dozers
Excavators
Tractors
Skid Steers
& More..

We stock common edges for OEM manufacturers including:
CAT
Komatsu
Volvo
Deere
Case
Bobcat
Hyundai
& More..

Some of our common stock edges include:

Grader Blades
Cleanup Edges
Half Arrow
Router Bits
Hot Cupped End Bits
End Bits
& More…

We stock and are able to build for any specific bucket manufacturer: Accurate, Craig, Weldco Beales, CWS, AMI, HNL, Lemac, Daequip, and any others!

System Operation Description:Switch circuits may have problems such as faulty wiring, faulty switches, or faulty connectors. Use the following diagnostic procedures in order to diagnose problems with these switch circuits and repair these switch circuits:
Engine ECM reset switch
Start aid manual override switch
Start/Run/Stop switchNote: The engine ECM reset switch is installed by the customer.These switches are normally open or normally closed.
Illustration 1 g01366881
Typical switch inputs and wiringTest Step 1. Check the Electrical Connectors and the Wiring
Remove the electrical power from the Electronic Control Module (ECM).
Illustration 2 g02164341
Location of the connectors that are for the switch circuits (typical left side engine view) (1) J1/P1 ECM connectors
Thoroughly inspect connectors (1) and the engine interface connectors. Thoroughly inspect the connections for the suspect switch. Refer to Troubleshooting, “Electrical Connectors – Inspect”. 4T3015 4T-3015 CAT 980 973 Loader End Cutting Edge
Illustration 3 g02219135
Terminal locations at the J1/P1 ECM connectors that are for the switch circuits (P1-22) Start aid manual override switch (P1-40) Start/Run/Stop switch (P1-41) Engine ECM reset switch
Illustration 4 g02219137
Terminals at the engine interface connector that are for the switch circuits (Terminal 9) Start aid manual override switch (Terminal 16) Start/Run/Stop switch
Perform a 45 N (10 lb) pull test on each of the wires in the circuit for the suspect switch.
Check the allen head screw on each ECM connector for the proper torque. Also, check the allen head screw on the customer connector for the proper torque. Refer to Troubleshooting, “Electrical Connectors – Inspect” for the correct torque values.
Check the harness and wiring for abrasions and for pinch points from the battery to the ECM.Expected Result:All connectors, pins, and sockets are coupled and/or inserted, and the harness and wiring are free of corrosion, of abrasion and of pinch points.Results:
OK – The wiring and connectors appear to be OK. Proceed to Test Step 2.
Not OK – There is a problem with the wiring and/or a connector.Repair: Repair the wiring and/or the connector. Replace parts, if necessary.